Backboard FAQ for Letters & House Numbers
What Is a Backboard for Sign Letters and House Numbers?
A backboard is the panel mounted behind your sign letters or house numbers. It gives the letters and numbers a solid mounting surface, improves contrast, and can hide wiring or old holes. Backboards are common on illuminated plaques, 3D letter sets, and house number signs.

Why Use a Backboard?
Hide the wiring
Every illuminated letter or house number has a power wire. By default, these wires are meant to pass through the wall and stay hidden behind it. Sometimes the wall is too thick, or there is no access to the back of the wall, so the wires cannot pass through. If they stay on the front, the wires are visible and look untidy.
A backboard lets you hide the wires behind the panel. All letter and number wires can be connected to one main line, so at most only one main wire is visible, and one wire is much easier to conceal. A backboard also covers old mounting holes and marks left by a previous sign.
Faster, easier installation
We pre-drill the mounting holes in the backboard and pre-install the letters or numbers on it. You only need to drill 4–6 holes to mount the complete sign. With individual letters, each letter usually needs 3–4 holes, so the backboard saves a lot of drilling and alignment work.
Pre-assembled power supply and controller
If you choose the pre-wired power supply and controller option, we mount the illuminated letters or numbers, power supply, and controller on the backboard before shipping. After delivery, you only need to drill the mounting holes, fix the sign, and connect the power. You can install it yourself and save the cost of an electrician. For complex RGBWW lighting with multiple wire connections, choosing a backboard with pre-assembled components saves a significant amount of installation time and labor cost.
What Size Should the Backboard Be?
The backboard is 2 inches larger than the letters or numbers. That gives about 1 inch of margin on each side. If you need a larger backboard, we can make it to your custom size.
The final size also depends on the font and the letters or numbers you choose. The charts below use house numbers as an example. The same 2-inch rule applies to backlit letters; size will be different with different fonts and letters or numbers. We can also make a custom backplate size.
Size chart for 6-inch numbers

Above is the backplate size chart for numbers 6 inches high, for reference only. Size will be different with different fonts and numbers. The backplate will be 2 inches bigger than the numbers. We can also make a custom backplate size.
Size chart for 8-inch numbers

Above is the backplate size chart for numbers 8 inches high, for reference only. Size will be different with different fonts and numbers. The backplate will be 2 inches bigger than the numbers. We can also make a custom backplate size.
What Material and Depth Are Used?
The backboard is made from 1 mm thick stainless steel, welded into a shell about 1 cm deep. The back is open by default.
The standard depth is 1 cm. We now also offer a deeper backboard option of about 3–5 cm, which can house the power supply and controller inside the backboard.


How Are the Letters, Numbers, and Wires Installed?
Yes, the backboard is pre-drilled for wires and mounting. We pre-install all the letters or numbers on the plate, and only one wire comes out for the power connection. That single wire is much easier to route and hide than a separate wire for every letter or number.
How Is the Backboard Mounted?
We normally use threaded rods to mount the backboard. For very large backboards, we can also provide side-mount brackets: fix the mounting brackets first, then lock the backboard onto them from the side.
For brick or masonry walls, use suitable masonry anchors. Seal the penetrations with exterior-grade sealant to keep water out.
Flat wall vs. uneven or curved wall
Choose the mounting method based on the wall surface:
- Flat, even wall: fix the backboard flat against the wall (direct wall mounting).
- Uneven, textured, or curved wall: use stand-off mounting so the backboard sits away from the wall on spacers. This bridges small surface differences and keeps the sign straight.


How Do I Clean and Maintain It?
Wipe the backboard with a damp cloth and mild soap. Avoid abrasive pads on brushed or mirrored finishes. Check the wall seals once a year and reseal them if needed.
What Colors Are Available?
The backboard can be finished in custom colors, just like the illuminated letters and house numbers. We recommend choosing a backboard color that contrasts with the letters or numbers, so the sign stays clear and readable in daylight.
Does a Backboard Affect Shipping Cost?
Yes. A backboard increases the package size considerably, which increases the freight cost and the total price. If you can make your own backboard locally, you can save part of this cost. A backboard can be made from a template, PVC, acrylic, stainless steel, or another suitable panel material.
If you prefer to make your own backboard, contact us and we can confirm the required dimensions and layout for your letters or numbers.
Pictures of Backlit Letters and Numbers with a Backboard



Custom Order
You can customize and order letters or house numbers with a backboard through our backlit house number product page. The price is quoted instantly, and you can also contact us for a custom size or a pre-assembled power and controller setup.
Browse backlit letters, illuminated address plaques and 3D metal house numbers for more options. For installation details, see the installation guide.